We bottled our first batch of mead. I thought we were going to get 25 bottles, but we ended up with 21. This batch was a cinnamon vanilla mead. It turned out great. Perhaps we sampled a bit more than I remember. Here’s an overview of the process we went through:
- Brewing Supplies: Fermenting Bucket, Glass Carboy, Filtered Funnel, Hydrometer, Thermometer, wine thief, airlock, rubber stopper, sanitizer, honey, sugar, yeast, yeast nutrients, cinnamon sticks, vanilla beans and campden tablets.

- Sanitization: Sanitize everything!
- Prepare the Must: I used 10 lbs of honey, 2 lbs of sugar and yeast nutrients to about 2 1/2 gallons of water heated to 160 degrees. The honey was easier to work with after letting it sit in a pot of warm water prior to adding to the must. Heating the must to 160 degrees pasteurizes the mix.

- Transfer to the Fermenting Bucket
- Increased the honey/sugar content: I wasn’t happy with the sugar content of the must. (I prefer sweet wines) After taking measurements with the hydrometer, I realized that I would end up with a dry wine if I didn’t increase the sugar content on the front end. I drew some of the must out of the fermenting bucket, returned it to the stock pot and added 3 more lbs of honey.
- Ready to start fermenting: I ended up with just a hair above 5 gallons of must in the primary fermenting bucket.

- Initial hydrometer reading: I used the wine thief to fill the hydrometer test tube. The initial hydrometer reading was 1.110. I added honey and sugar to bring the reading to 1.132.

- Added campden tablets: Even though the pasteurization process should have killed off any wild yeasts or bacteria, I still added campden tablets and waited a day for them to finish working
- Activating the yeast: I used Lalvin D47 and just follwed the instructions for activation in warm water

- Pitching the yeast: Emily pitched the yeast into the must to start the fermentation process

- Airlock: Everything sealed up nicely with the airlock installed so no bacterial nasties get in. I like to use vodka in the airlock rather than water.

- Racking the mead: The fermentation process bubbled along nicely for a couple of weeks. After the bubbling in the airlock slowed to around 30 seconds between each bubble, I racked the mead from the primary fermenting bucket to the secondary fermenter, a glass carboy. I decided to buy a larger glass carboy than the one that was in the first pic. To move the mead from the primary to the secondary, I siphoned the mead with a racking cane and hose. I used the filtered funnel on the glass carboy. To get the most mead out, I had to elevate one corner of the primary. My Alcoholic Beverage Control Laws and Rules of North Carolina book was just the right size to wedge under the fermenter.



- Second Hydrometer Reading: Using the wine thief, test tube and hydrometer again, I got a reading of 1.028.

- Secondary Fermentation: Everything all sealed up in the glass carboy for the secondary fermentation. I added 6 cinnamon sticks and 6 tahitian vanilla beans (sliced lengthwise)


- 09/09/10, Third Hydrometer Reading: This reading was 1.03, which calculates into 13.5% ABV. I tasted a sip. It was sweet with a strong, but not overpowering cinnamon flavor and a hint of vanilla. The clarity is great.

- 10/02/10, Added Bentonite: Bentonite is a type of clay used as a clarifying agent before bottling.
- 10/06/10, Fourth Hydrometer Reading: This reading was 1.028, which calculates into 13.78% ABV, Check out that clarity! Time to bottle.

- Preparing the Bottles: Bottles have been sanitized and dried on the drying tree.

- Filling the Bottles: The mead was racked back into the primary, which has a spigot for bottling. The bottles were filled by hand.

- Corking: I have a floor corker that I used to cork the bottles. I used synthetic corks.


- Wax seals: I decided that I wanted to wax seal the bottles. It just seemed like it added quite a bit in the presentation of the final product. I melted wax beads in a can set in boiling water. Dipped the ends of the corked bottles and rolled them around to get the wax even. Ready for labels.



- Labeling: I bought printer-ready labels that matched the wax seals and added my own custom touch to the labels. The finished product looks great!

- The labels read: Orr Family Meadery, Metheglin 2010, Me·theg·lin is a variety of spiced mead (honey-wine). This particular bottle contains a fermentation of sweet mead infused with the flavors of cinnamon and vanilla. Brewed especially for friends and family of Marcus & Lauren Orr. Alcohol 14% by Volume 750ML




